Difference between revisions of "SPI LCD"
Jump to navigation
Jump to search
(Redirected page to LCD) |
|||
| (28 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
#REDIRECT [[LCD]] |
|||
[[File:SPI_LCD.jpg|thumb|300px|alt=The SPI_LCD board|The SPI_LCD board]] |
|||
This is the documentation page for the SPI_LCD board. |
|||
== Overview == |
|||
== Assembly instructions == |
|||
The board comes assembled. No assembly required. |
|||
=== Possible Configurations === |
|||
The board could be configured with software for I2C. |
|||
== External resources == |
|||
=== Datasheets === |
|||
[http://www.atmel.com/Images/doc8006.pdf The datasheet of the Attiny44 processor] that is the "brains" of the board. |
|||
SPI connector: |
|||
[http://www.batsocks.co.uk/readme/isp_headers.htm We use the 6-pin header]. The pin labeled "RESET" when the connector is used as ICSP header should be labeled "slave select" when used for SPI datatransfer. |
|||
== Additional software == |
|||
=== Related projects === |
|||
== Pinout == |
|||
=== SPI === |
|||
[[SPI connector pinout]] |
|||
=== LCD === |
|||
{| border=1 |
|||
! pin !! name |
|||
|- |
|||
| 1 || VSS |
|||
|- |
|||
| 2 || VDD |
|||
|- |
|||
| 3 || VO (contrast) |
|||
|- |
|||
| 4 || RS |
|||
|- |
|||
| 5 || RW (GND) |
|||
|- |
|||
| 6 || EN |
|||
|- |
|||
| 7 || DB0 (NC) |
|||
|- |
|||
| 8 || DB1 (NC) |
|||
|- |
|||
| 9 || DB2 (NC) |
|||
|- |
|||
| 10 || DB3 (NC) |
|||
|- |
|||
| 11 || DB4 |
|||
|- |
|||
| 12 || DB5 |
|||
|- |
|||
| 13 || DB6 |
|||
|- |
|||
| 14 || DB7 |
|||
|- |
|||
| 15 || BL + (VCC) |
|||
|- |
|||
| 16 || BL - (PWM) |
|||
|- |
|||
|} |
|||
=== LEDs === |
|||
None. The board doesn't have leds. The next hardware revision might have a powerled. |
|||
== Jumper settings == |
|||
There are two solder jumpers. The one between the two 6-pin SPI connectors controls the function of the SPI connector nearest the I2C connectors. |
|||
In the default configuration the second SPI connector is a daisy-chain connector for the SPI bus. |
|||
In the other configuration, the second SPI connector is the ICSP connector. |
|||
The second solder jumper connects "rs" and "vo" of the LCD together (and to one pin of the attiny44 controller on the board) in the default configuration. |
|||
In the other configuration, the pin used for SPI slave select can be used as the RS pin. This is used in the I2C configuration. |
|||
See [[solder jumpers]] for more information on how to change the setting. |
|||
== Programming == |
|||
To display a string on the LCD, just send over SPI the same bytes you would send to LCD, prefixed with the address of the LCD (the default address is 0x82). |
|||
Bytes above 0xf0 are "special". |
|||
0xf0 <xy> is set cursor. the <xy> byte is 3 bit line number and 5 bit position number. This addressing allows up to 8 lines of 32 characters. |
|||
0xf1 is clear LCD. |
|||
0xf2 <addr> is "set address". If you want to change the address the module reacts to. The address is stored in eeprom, and will remain this way after a powercycle. |
|||
0xf3 <contrast> is "set contrast". This will set the contrast to the value you specify. 0x40 is the default that works fine for the LCDs that we have. |
|||
0xf4 <backlight> is the "set backlight intensity" command. This will set the backlight intensity to the value specified. |
|||
0xf5 <byte> will send the byte as a command to the HD44780. You need this for example to use the user-defined characters. |
|||
0xff <byte> will send the byte to the LCD without special character processing. This allows you to send codes 0xf0 through 0xff to the LCD if required. |
|||
Other bytes between 0xf0 and 0xff are reserved and are currently implemented as a no-op. |
|||
When you send a "read" request there are two different commands: |
|||
0x01: "Identify". The board will respond with "spi_lcd 1.2". The version number is subject to change of course. The string is zero-terminated. |
|||
0x02: "serial number". The board will respond with the 32-bit serial number. (After that the remaining bytes of the eeprom will be sent). |
|||
== The software == |
|||
== Default operation == |
|||
== Future hardware enhancements == |
|||
== Future software enhancements == |
|||
== Changelog == |
|||
=== 1.2 === |
|||
* Initial public release |
|||
Latest revision as of 15:51, 21 May 2012
Redirect to: