DIO protocol

Introduction

The protocol for the DIO, 3FETs, 7FETs, RELAY and Pushbutton will be explained on this page. Most functions apply to all boards, but some don't.

This page describes both the SPI and the I2C version. See SPI versus I2C protocols for the explanation about how the protocols work in general.

Please see this page for the default adresses.

write ports

On the DIO and related boards all ports just set a single value. So writing more than one byte to such a port is redundant. The last value is the one used. The DIO boards don't have any ports that are logically a stream of bytes. So writing more than one or two bytes is not encouraged.

The DIO, 3FETS and 7FETS boards define several ports:

port	available on				function
	DIO	3/7FETs	RELAY	pushbutton
0x10	X	X	X		set all outputs (bit 0 is output 0, etc).
0x20 .. 0x27	X	X	X		set one output (0x20 for output 0, 0x21 for output 1 etc)
0x30	X	X	X		define pins as inputs or outputs. 0 means input, 1 means output.
0x40	X	X			set current position.
0x41	X	X			set target position.
0x42	X	X			set relative position.
0x43	X	X			set stepdelay. (in tenths of a microsecond, default 200: 20ms between steps).
0x50 .. 0x57	v1.1 and up	X			Set PWM value. 0x50: output 0, 0x51 output 1 etc.
0x5f	v1.1 and up	X			Set PWM mask. PWM is enabled on the outputs, who's bit is high. send 0x01 as data, to enable PWM on output 0
0x70 .. 0x77	v1.2 and up				Select which i/o is coupled to which ADC channel
0x80	v1.2 and up				Set number of ADC channels to read
0x81	v1.2 and up				Set number of samples to add (use a power of 2) (two bytes)
0x82	v1.2 and up				Set ammounts of bits to shift accumulated sample value
0xf0	X	X	X	X	change address.

All the above ports are read/write. I.e. if you read from that port, you will get the current value.

read ports

The DIO, 3FETS, and 7FETS boards support the following read ports:

port	available on				function
	DIO	3/7FETs	RELAY	pushbutton
0x01	X	X	X	X	identification string. (terminated with 0).
0x02	X	X	X	X	read eeprom (serial number).
0x10	X			X	read all inputs
0x20 .. 0x27	X			X	read one input (0x20 for input 0, 0x21 for input 1 etc)
0x40	X	X			read current position.
0x41	X	X			read target position.
0x43	X	X			read stepdelay. (in tenths of a microsecond, default 200: 20ms between steps).
0x50	v1.1 and up	X			Return PWM value for output 0
0x51	v1.1 and up	X			Return PWM value for output 1
0x52	v1.1 and up	X			Return PWM value for output 2
0x53	v1.1 and up	X			Return PWM value for output 3
0x54	v1.1 and up	X			Return PWM value for output 4
0x55	v1.1 and up	X			Return PWM value for output 5
0x56	v1.1 and up	X			Return PWM value for output 6
0x5f	v1.1 and up	X			Return PWM mask. PWM is enabled on the outputs, who's bit is high. send 0x01 as data, to enable PWM on output 0
0x60.. 0x67	v1.2 and up				Return analog value (2 bytes)
0x68 .. 0x6f	v1.2 and up				Return avaraged analog value (2 bytes)
0x70 .. 0x77	v1.2 and up				Return which i/o is coupled to which ADC channel
0x80	v1.2 and up				Return number of ADC channels to read
0x81	v1.2 and up				Return number of samples to add (two bytes)
0x12	v1.2 and up				Return ammounts of bits to shift accumulated sample value

Using the analog inputs

Will be addad ASAP (nov. 12 2012)

examples

For SPI in the examples below, "data sent" means the data on the MOSI line, while "data received" means the data on the MISO line. when MISO reads "xx" you should ignore the data. When MOSI reads "xx" it doesn't matter what you send.

For I2C in the examples below, you should first initiate a "write" transaction with the data in the "data sent column". Don't send the "xx" bytes. Then you initiate a "read" transaction, and you will get the data in the "data received" column (and again not the "xx" bytes).

read identification

read the identification string of the board. (SPI_DIO)

data sent	data received	explanation
0x85	xx	select destination with address 0x84 for READ.
0x01	xx	identify
xx	0x73	's'
xx	0x70	'p'
xx	0x69	'i'
xx	...	etc.

read the identification string of the board. (I2C_DIO)

I2C master	I2C slave (i2c_dio)	explanation
START	--	start I2C transaction
0x84	--	select destination with address 0x84 for write (set port).
0x01	--	identify
STOP	--	terminate I2C transaction.
START	--	start I2C transaction
0x85	--	select destination with address 0x84 for READ.
--	0x69	'i'
--	0x32	'2'
--	0x63	'c'
--	...	etc.

Note that in the SPI example, there is bidirectional datatransfer on every cycle, but the data is "don't care" or "must ignore" (indicated by xx), while in the I2C case, the other side cannot send as there is only one data-transfer direction (indicated by "--").

turn on all outputs

data sent	data recieved	explanation
0x88	xx	select destination with address 0x88 for WRITE
0x10	xx	set outputs as in bitpattern (next byte)
0xff	xx	All outputs active.

turn on output 4

data sent	data recieved	explanation
0x88	xx	select destination with address 0x88 for WRITE
0x24	xx	port 0x24: output 4...
0xff	xx	... active.

move stepper to step 0x1234

data sent	data recieved	explanation
0x88	xx	select destination with address 0x88 for WRITE
0x41	xx	port 0x41: set target position
0x34	xx	low byte
0x12	xx	high byte.