This is the documentation page for the RGB clock kit.
Driver PCB for up to 64 common-anode RGB LEDs, or 192 normal LEDs.
The PCB is designed for 1:3 multiplexing of the LEDs, and is equipped with 8 74HC595 shift registers (configured as 4 16-bit deep registers), 64 current-limiting resistors (220 Ohm by default) and 3 FETs to switch the cathode groups on-and-off.
The PCB is equipped with a BitWizard-standard 20-pin IO connector, designed to work together with our USB-multio PCB, but it is also possible to connect our FTDI-ATmega, USB-bigmultio or Cyclone dev board, or one of your own boards, like for example an Arduino.
SV1-SV8 are the connectors for the RGB LEDs. SV1-SV8 are connected to IC1-IC8.
IC1 and IC5 are configured as one 16-bit deep shift register. Qa-Qh are connected to IC1, and Qi-Qp are connected to IC5.
IC2 and IC6 are configured as one 16-bit deep shift register. Qa-Qh are connected to IC2, and Qi-Qp are connected to IC6.
IC3 and IC7 are configured as one 16-bit deep shift register. Qa-Qh are connected to IC3, and Qi-Qp are connected to IC7.
IC4 and IC8 are configured as one 16-bit deep shift register. Qa-Qh are connected to IC4, and Qi-Qp are connected to IC8.
The control pins (!OE, LATCH, !RESET, CLK) of all shift registers are connected in parallel.
SER0 is connected to IC1.
SER1 is connected to IC2.
SER2 is connected to IC3.
SER3 is connected to IC4.
It is therefore required to update all shift registers at the same time.
Assembling the kit
LED Driver PCB
- First, decide if you want to use 4 pushbutton switches (for the default firmware), 4 LEDs, or a mix (for custom firmware).
- SW1 and R65 or D7 and R71
- SW2 and R66 or D6 and R72
- SW3 and R67 or D5 and R73
- SW4 and R68 or D4 and R74
- Mount all necessary SMD components. Which component should go where, can be found in the table below.
- cut the header strips to the right length. Our suggestion:
- cut the first strip in one 10-pin long strip, and 5 6-pin long strips.
- cut the second header in 3 6-pin strips, and one 4-pin strip.
- solder all headers in place
- solder the desired switches in place
Component Value IC1-IC8 74HC595 R1-R64 220R R65-R68 10K R69-R74 1K C1-C8 100nF C9 10uF T1-T3 N-channel FET D1 Double Diode (BAT54S for example) D2-D7 LED SW1-SW4 Pushbutton
Counting clockwise, starting at the LED to the right of the topmost LED:
Output Pin# Connector Qp 8 SV6 Qo 7 SV6 Qn 6 SV6 Qm 5 SV6 Ql 4 SV6 Qk 3 SV6 Qj 2 SV6 Qi 1 SV6 Qg 7 SV2 Qf 6 SV2 Qe 5 SV2 Qd 4 SV2 Qc 3 SV2 Qb 2 SV2 Qa 1 SV2
All R, G and B pins should be connected in parrallel.
This is the same for each quadrant, only the connector numbers differ.
Putting it all together
SV10 is connected as follows
|14||external clock source|
SV1 through SV8 are connected as follows:
SV9 can be used to connect an external clock source, or a servo motor, or...
|3||connected to pin14 form SV10|
Pin 3 has two clamping diodes attached, to limit the voltage range to GND-0.6V and VCC+0.6V.
- D2 is connected to VCC from SV10
- D3 is connected to USB power
- D4 is connected to pin17 from SV10
- D5 is connected to pin18 from SV10
- D6 is connected to pin15 from SV10
- D7 is connected to pin16 from SV10
- Switch1 (next to R71) is connected to pin16 from SV10
- Switch2 (next to R72) is connected to pin15 from SV10
- Switch3 (next to R73) is connected to pin18 from SV10
- Switch4 (next to R74) is connected to pin17 from SV10
JP1: Power supply selection.
Open: LED driver board and microcontroller board have individual power supplies
Closed: VCC from LED driver board and microcontroller board are connected.
If the complete device is powered from the microcontroller board, the jumper can be replaced with a toggle switch. This allows you to turn the LEDs on and off, without affecting timekeeping.
The software supplied by BitWizard, is designed to run on the BitWizard Multio board, but it should be possible to port it to other boards. A link to the sources will be posted within a few days (It's Jan 9th 2012 at the moment).
Future hardware enhancements
- Replace 2 12-pin connectors by 1 20-pin connector
- Add numbers to the pushbutton switches
- Initial public release