FT2232H breakout board
FT2232H breakout board
This is the documentation page for the FT2232H breakout board.
overview
The FT2232H breakout board has an USB connector, two 20-pin HDR-standard IO connectors (one for BUS0 and one for BUS1), and one 40-pin terasic compatible connector. The brains of the PCB, of course, is an FT2232H chip.
External resources
pinout
The SV1 connector is designed to be connected to the 40 pin expansion connector of Terasic FPGA boards. This can be done with a standard 40 pin IDE cable, provided that it isn't too long.
40-pin connector SV1 is connected as follows:
| 1 | ACBUS5 |
| 2 | NC |
| 3 | NC |
| 4 | NC |
| 5 | ADBUS0 |
| 6 | ADBUS1 |
| 7 | ADBUS2 |
| 8 | ADBUS3 |
| 9 | ADBUS4 |
| 10 | ADBUS5 |
| 11 | 5V |
| 12 | GND |
| 13 | ADBUS6 |
| 14 | ADBUS7 |
| 15 | ACBUS0 |
| 16 | ACBUS1 |
| 17 | ACBUS2 |
| 18 | ACBUS3 |
| 19 | ACBUS4 |
| 20 | ACBUS5 |
| 21 | ACBUS6 |
| 22 | ACBUS7 |
| 23 | BDBUS0 |
| 24 | BDBUS1 |
| 25 | BDBUS2 |
| 26 | BDBUS3 |
| 27 | BDBUS4 |
| 28 | BDBUS5 |
| 29 | 3V3 |
| 30 | GND |
| 31 | BDBUS6 |
| 32 | BDBUS7 |
| 33 | BCBUS0 |
| 34 | BCBUS1 |
| 35 | BCBUS2 |
| 36 | BCBUS3 |
| 37 | BCBUS4 |
| 38 | BCBUS5 |
| 39 | BCBUS6 |
| 40 | BCBUS7 |
Connectors SV4 and SV5 are designed to be compatible with the 20-pin IO connectors also found on other BitWizard boards.
20-pin connector SV4 is connected as follows:
| 1 | GND |
| 2 | GND |
| 3 | ADBUS0 |
| 4 | ADBUS1 |
| 5 | ADBUS2 |
| 6 | ADBUS3 |
| 7 | ADBUS4 |
| 8 | ADBUS5 |
| 9 | ADBUS6 |
| 10 | ADBUS7 |
| 11 | ACBUS0 |
| 12 | ACBUS1 |
| 13 | ACBUS2 |
| 14 | ACBUS3 |
| 15 | ACBUS4 |
| 16 | ACBUS5 |
| 17 | ACBUS6 |
| 18 | ACBUS7 |
| 19 | 3V3 |
| 20 | 3V3 |
| GND | 1 | 2 | GND |
| ADBUS0 | 3 | 4 | ADBUS1 |
| ADBUS2 | 5 | 6 | ADBUS3 |
| ADBUS4 | 7 | 8 | ADBUS5 |
| ADBUS6 | 9 | 10 | ADBUS7 |
| ACBUS0 | 11 | 12 | ACBUS1 |
| ACBUS2 | 13 | 14 | ACBUS3 |
| ACBUS4 | 15 | 16 | ACBUS5 |
| ACBUS6 | 17 | 18 | ACBUS7 |
| 3V3 | 19 | 20 | 3V3 |
20-pin connector SV5 is connected as follows:
| GND | 1 | 2 | GND |
| BDBUS0 | 3 | 4 | BDBUS1 |
| BDBUS2 | 5 | 6 | BDBUS3 |
| BDBUS4 | 7 | 8 | BDBUS5 |
| BDBUS6 | 9 | 10 | BDBUS7 |
| BCBUS0 | 11 | 12 | BCBUS1 |
| BCBUS2 | 13 | 14 | BCBUS3 |
| BCBUS4 | 15 | 16 | BCBUS5 |
| BCBUS6 | 17 | 18 | BCBUS7 |
| 3V3 | 19 | 20 | 3V3 |
- led1 is connected to VCC
Jumper settings
For 2.0
SV2: 3V3 supply selection
1-2: Direct from FPGA board (through 40-pin connector)
2-3: From regulator (see SV3 settings)
SV3: Regulator power source selection
1-2: Powered from USB
2-3: Powered from FPGA board (through 40-pin connector)
For 2.1
J1: 3V3 supply selection
1-2: Direct from FPGA board (through 40-pin connector)
2-3: From regulator (see SV3 settings)
J2: Regulator power source selection (physical position is the same as in 2.0, only numbering has changed)
1-2: Powered from FPGA board (through 40-pin connector)
2-3: Powered from USB
future hardware enhancements
Changelog
2.1
- Renamed SV2 to J1
- Renamed SV3 to J2
- Jumper settings marked on PCB
- Moved center of mounting holes to 3mm from PCB edge
2.0
- Initial public release